Cut Edge Belts

Classical section v-belts
Wedge section v-belts
Narrow v-belts
Banded belts

Classical Section Cut Edge

Aktiv classical section cut edge belts can be used in both light and heavy mechanical engineering applications, and the advantages are as follows:

  • Higher rate of power transmission efficiency
  • Able to transmit more power, so more value for money
  • Use small drive space due to the need of smaller diameter pulley
  • Longer service life and low maintenance
  • Power rating is about 30% over wrapped belts because of the high belt flexibility
  • No modifications needed when using on the existing drive
  • From practical field test, energy saving is as high as 8%

Product Features:

  • Matching-free
  • Working temperature from - 30oC to + 90oC
  • High resistances to fire and oil
Technical Data:
Section Dimensions Angle Range Nominal Min Rec.
Top width
(mm)		 Thickness
(mm)		 (Deg.) Min.
(inches)		 Max.
(inches)		 Length
(inches)		 Pulley Dia.
Dp (mm)
ZX 10 6.0 36 24 220 Li 40
AX 13 8.0 36 24 220 Li 60
BX 17 11.0 36 24 200 Li 100
CX 22 14.0 36 24 200 Li 160

Wedge Section Cut Edge

Aktiv narrow raw edge v-belts are good for the light and heavy mechanical engineering applications in many industries with outstanding advantages as follows:

  • Higher rate of transmission efficiency
  • Enhanced power transmission capacity up to 75% superior to these of the conventional belts due to very low energy consumption
  • Longer service life and low maintenance
  • Less number of belts required when designing new drive

Product Features:

  • High resistances to heat, oil and abrasion with excellent lateral stability due to the use of anisotropic fiber and polychloroprene rubber compound
  • High flexibility allows smaller pulley diameters and drive ratios up to 1:12
  • Working temperature between - 30oC to + 90oC
Technical Data:
Section Dimensions Angle Range Nominal Min Rec.
Top width
(mm)		 Thickness
(mm)		 (Deg.) Min.
(inches)		 Max.
(inches)		 Length
(inches)		 Pulley Dia.
Dp (mm)
XPZ 10 8.0 36 600 6080 Lp 54
XPA 13 10.0 36 600 6080 Lp 80
XPB 17 14.0 36 600 6080 Lp 128
XPC 22 18.0 36 600 6080 Lp 180

Narrow Cut Edge Belts

Aktiv cut edge belts are introduced for the mechanical engineering application of both light and duty where space, weight and horsepower capacity are critical. The characteristics of this belt are as follows:

  • Higher efficiency
  • Enhanced power transmission capacity
  • High horsepower rating of the belt needs just about 1/3 of the space needed by classical v-belts

Product Featues:

  • Longer service life and low maintenance
  • High resistance to heat and oil-limited elongation after running in
  • Matching-free
  • Working temperature between - 30oC to + 90oC
Technical Data:
Section Dimensions Angle Range Nominal Min Rec.
Top width
(mm)		 Thickness
(mm)		 (Deg.) Min.
(inches)		 Max.
(inches)		 Length
(inches)		 Pulley Dia.
Dp (mm)
3VX 9.7 8.0 36 24 200 La 55
5VX 16 14.0 36 24 220 La 112
8VX 25 23.0 36 24 200 La 254

Banded Belts

In terms of belt's performance, Aktiv banded V-belts offer the following advantages in comparing to single v-belts:

  • No slippage between the v-belts
  • Very good in Horizontal drives when needed
  • Better absorption of shock loads

Product Features:

  • Permanent matched set
  • No lateral whip, spin or jump-off
  • Do not need deep pulley grooves even on horizontal drives
  • High resistance to heat and oil
  • Working temperature ranging from - 30oC to + 90oC
Technical Data:
Section Dimensions Angle Range Pitch Between Two Belts
Top width
(mm)		 Thickness
(mm)		 (Deg.) Min.
(inches)		 Max.
(inches)		 (mm)
HAX 13.0 10.0 36 600Li 5080 15.9
HBX 16.0 14.0 36 600Li 5080 19.0
HCX 25.0 23.0 36 600Li 5080 25.5
HXPZ 10.0 10.0 36 600Li 5080 12.0
HXPA 13.0 12 36 600Lp 5080 15.0
HXPB 17.0 16 36 600Lp 5080 19.0
HXPC 22.0 20 36 600Lp 5080 25.5
H3VX 9.7 10 36 24"La 5080 10.3
H5VX 15.8 16 36 24"La 5080 17.5